POSITION:HOME > QUESTION

QUESTION

Causes and solutions for large pressure drop of brazed plate heat exchanger

Causes of large pressure drop in plate heat exchangers
1. the operating system pipeline is not properly purged, especially in the new installation system pipeline, many dirt (such as welding slag) into the interior of the plate heat exchanger, due to the plate heat exchanger The cross-sectional area of ??the flow channel is narrow, and the sediment and suspended matter in the heat exchanger gather in the corner hole and the flow guiding area, so that the flow channel area at the place is greatly reduced, and the pressure is mainly lost in this part.
2, after the plate heat exchanger has been running for a period of time, the pressure drop caused by the surface fouling of the plate is too large.
3. when the plate heat exchanger is selected for the first time, the area is too small, causing the flow rate between the plates to be too high and the pressure drop to be too large.
Processing method for large pressure drop of plate heat exchanger
1. remove dirt or plate fouling in the heat exchanger flow channel, for the newly run system, clean once a week according to the actual situation. When cleaning the surface scale of the plate (mainly CaCO3), use a 0.3 sulfamic acid solution or a 0.8 nitric acid solution containing 0.3 urotropin, 0.2 aniline, 0.1 potassium thiocyanate as the cleaning solution, and the cleaning temperature is 40-60 °C. When disassembling the equipment for chemical immersion cleaning, open the heat exchanger inlet and outlet of the heat exchanger, or install the DN25 cleaning port on the medium inlet and outlet nozzles when installing the equipment, inject the prepared cleaning liquid into the equipment, and wash it with water after immersion. Clean the residual acid to make pH≥7. When disassembling the cleaning, soak the plate in the cleaning solution for 30 minutes, then use a soft brush to lightly scale the scale, then rinse it with water. Avoid damage to the plates and rubber pads during the cleaning process. If the mechanical backwashing method is not disassembled, a nozzle shall be connected to the medium inlet and outlet pipes in advance, and the equipment shall be connected to the mechanical cleaning vehicle, and the cleaning liquid shall be injected into the equipment in the opposite direction of the medium flow, and the circulation cleaning time is 10 to 15 minutes. The medium flow rate is controlled at 0.05 to 0.15 m/s. After that, it is recycled several times with clean water to control the mass concentration of Cl in the water below 25 mg/I.
2. secondary circulating water is good to use soft water after softening treatment, generally requires the concentration of suspended solids in water is not more than 5mg / L, impurity diameter is not more than 3mm, pH & ge; When the water temperature is not more than 95 °C, the concentration of Ca and Mg should be no more than 2mmol/L; when the water temperature is greater than 95°C, the concentration of Ca and Mg should be no more than 0.3mmol/L, and the concentration of dissolved oxygen should be no more than 0.1mg/L.
3. for the central heating system, you can use a secondary water supply method.
2019/05/11 09:48:47 5055 Click

主站蜘蛛池模板: 在线免费观看韩国a视频| 日韩中文字幕视频在线观看 | 国产亚洲精品无码专区| 国产日韩精品一区二区三区| 免费体验120秒视频| 中文字幕一区二区区免| 精品国产麻豆免费人成网站| 无需付费看视频网站入口| 国产a级特黄的片子视频| 久久免费视频网| 美团外卖chinesegayvideos| 无码任你躁久久久久久老妇 | 精品乱码久久久久久久| 大陆三级理论电影有哪些| 动漫美女羞羞网站| 一本一道dvd在线观看免费视频| 熟妇激情内射com| 国产精品28p| 中文字幕在线成人免费看| 被夫の上司持久侵犯奈奈美| 日韩亚洲av无码一区二区三区| 啊灬啊别停灬用力啊老师在线 | 福利一区在线观看| 国产精品欧美一区二区三区不卡 | 亚洲香蕉久久一区二区三区四区| 一个人看的www在线观看免费| 欧美综合自拍亚洲综合图| 国产成人女人在线视频观看| 久久精品99久久香蕉国产| 精品人妻少妇一区二区三区| 国产精品成人无码久久久| 久久er这里只有精品| 波多野结衣精品一区二区三区| 在线无码午夜福利高潮视频| 亚洲av无码国产精品麻豆天美| 色欲综合久久中文字幕网| 在私人影院里嗯啊h| 久久天天躁狠狠躁夜夜| 色偷偷女男人的天堂亚洲网| 成人看片黄a毛片| 免费无码国产V片在线观看|